About the ASI SI Series Surface Insensitive Cyanoacrylate
ASI SI Series Cyanoacrylate is a super glue used in applications that require fast cure speeds. The SI Series super glue is perfect for bonding difficult substrates, acidic surfaces, wood, PVC and substrates that contain plasticizers like certain types of EPDM, etc.
The SI Series super glue from ASI is the go-to super glue for most applications where a strong, permanent bond and fast set times are required.
Benefits of the ASI SI Series Cyanoacrylates
- Bonds almost any substrate
- Faster than most super glues
- Single component (no mixing or nozzles required)
- Cures at room temperature
- Good for bonding most substrates
- Fast cure time
- Dispensing can be automated
- Long term bonds
- Economical
- Meets most military (MilSpec) standards
- Can replace heavy mechanical fasteners
Compare ASI SI 5 to
- 3M PRODUCTSTM CA-40
- ARON ALPHATM 221 / 221F
- CHEMENCETM SI-5
- HENKELTM 8300
- HERNONTM 108
- LOCTITETM 406
- PACERTM RX-5,
- PERMABONDTM 790
Compare ASI SI 30 to
- ARON ALPHATM 231F
- CHEMENCETM SI 50
- HERNONTM 124
- PACERTM RX 50
- PERMABONDTM 791
Compare ASI SI 120 to
- ARON ALPHATM 232 / 202F
- CHEMENCETM SI 100
- HERNONTM 135
- LOCTITETM 401
- PACERTM RX 100
- PERMABONDTM 792
Compare ASI SI 500 to
- 3 BONDTM 1786
- ARON ALPHATM 252F /282F
- BOSTIKTM 7433
- CHEMENCETM SI 600
- CIBA-GEIGYTM C - 11
- HERNONTM 134
- LOCTITETM 447
- LORDTM R
- PACERTM RX 500
- PERMABONDTM 795
Compare ASI SI 1500 to
- CHEMENCETM SI 1500
- PACERTM RX 700
- PERMABONDTM 798
Compare ASI SI 2000 to
- PERMABONDTM 799LV
Compare ASI SI 4000 to
- ARON ALPHATM 253TX
- PERMABONDTM 799
Compare ASI SI GEL to
- CHEMENCETM SI GEL
- HERNONTM 138
- LOCTITETM 454
* The product names used in this website are for identification purposes only.
* All trademarks and registered trademarks are the property of their respective owners.
ASI SI Series Surface Insensitive Cyanoacrylate Specifications
- Color: Clear
- Viscosity: 120 cps
- Specific Gravity: 1.05
- Base: Modified Ethyl
ASI SI Series Chemical and Solvent Resistance
Percent of Strength Retained After Aging for 500 Hours
- GASOLINE @ 220C: 100%
- ISOPROPANOL @ 220C: 100%
- ETHANOL @ 220C: 100%
- FREON TA @ 220C% 100%
- MOTOR OIL @ 400C% 100%
- POLYCARBONATE 400C @ 95% RH 100%
ASI SI Series Cure Time and Bond Strength By Substrate
- Steel < 10 Seconds > 2100 psi
- Aluminum < 10 Seconds > 1750 psi
- Neoprene < 5 Seconds > 750 psi
- ABS < 10 Seconds > 900 psi
- PVC < 10 Seconds > 900 psi
- Polycarbonate < 10 Seconds > 900 psi
- Phenolic < 10 Seconds > 850 psi
| PRODUCT | GAP FILL | VISCOSITY | STRENGTH | TEMP RANGE | CURE SPEED (FIXTURE/FULL) | MIL SPEC A 46050C |
| SI 5 | 0.002 | 5 cps | 2800/4200 | -65 to 200? F | <5 Sec/8 Hours | Type II, Class 1 |
| SI 30 | 0.004 | 30 cps | 2800/4200 | -65 to 200? F | <5 Sec/8 Hours | Type II, Class 1 |
| SI 120 | 0.006 | 120 cps | 2800/4200 | -65 to 200? F | <8 Sec/8 Hours | Type II, Class 2 |
| SI 500 | 0.007 | 500 cps | 2800/4200 | -65 to 200? F | <8 Sec/8 Hours | Type II, Class 2 |
| SI 1000 | 0.008 | 1,000 cps | 2800/4200 | -65 to 200? F | <8 Sec/8 Hours | Type II, Class 3 |
| SI 1500 | 0.008 | 1,500 cps | 2800/4200 | -65 to 200? F | <8 Sec/8 Hours | Type II, Class 3 |
| SI 2000 | 0.009 | 2,000 cps | 2800/4200 | -65 to 200? F | <8 Sec/8 Hours | Type II, Class 3 |
| SI 3200 | 0.009 | 3,200 cps | 2800/4200 | -65 to 200? F | <10 Sec/8 Hours | Type II, Class 3 |
| SI 5000 | 0.009 | 5,000 cps | 2800/4200 | -65 to 200? F | <10 Sec/8 Hours | Type II, Class 3 |
| SI GEL | 0.01 | Gel | 2800/4200 | -65 to 200? F | <10 Sec/8 Hours | Type II, Class 3 |
ASI SI Series Cyanoacrylate Data Sheets
ASI SI Series Technical Data Sheets
ASI SI Series Material Safety Data Sheet
WASHING INSTRUCTIONS:
Machine wash separately in cold water on a gentle cycle. Tumble dry separately on low heat. Add QE Home Wool Dryer Balls to reduce wrinkles and increases drying efficiency. Touch up with a low heat iron as needed. Do not bleach or dry clean.
